Primo water dispensers come in a variety of models and designs, but they all have one thing in common. They all feature a quick-dispense system that allows you to quickly get a glass of cold water for when you’re feeling thirsty. When they get won out, you may wish to know how to dispose of primo water dispenser.
Primo water dispensers can be used to dispense both hot and cold water, depending on which model you purchase. However, the nature of these machines makes them difficult to clean and maintain. This is why we’ve created this guide to help individuals dispose off Primo Water Dispenser safely and efficiently.
Dispose off Primo water dispenser
Primo water dispensers often come with a variety of different features. They might be multi-purpose and dispense both cold and hot water, or they might be exclusively for cold water. Primo water dispensers are usually more expensive than other types of water dispensers, but they also have a longer life span.
However, this type of water dispenser is more difficult to clean because the parts are not dishwasher safe. This means that you will need to scrub them by hand. The best way to dispose off your Primo Water Dispenser is to first remove the spigot from the machine by unscrewing it from the bottom of the unit.
You’ll then want to use a sponge and dish soap to thoroughly clean out the inside of the machine so that there are no traces of residue left behind on any of the surfaces. To finish cleaning your Primo Water Dispenser, you can use a soft cloth dipped in vinegar or lemon juice to wipe down any remaining surfaces.
Make sure all the water is drained
Before you take your Primo water dispenser to the recycling station, make sure that all of the water is drained. You can use a plunger or make a spill-proof seal by using a damp cloth wrapped around the faucet and twisting it tightly. After making sure that there is no more water left in the machine, turn off the power supply by unplugging it.
Then, unscrew the six screws on top of the water tank and lift up the lid. Grasping both sides of the tank with your hands, twist and pull to remove it from its position. Remove any remaining water from inside the tank before disposing it off in a nearby sink or tub.
Check for any leftover parts in this area and remove them as well for disposal purposes. Now you’re ready to recycle your old Primo water dispenser. Take it to your local recycling station where they’ll dispose of it correctly and responsibly per their regulations.
Related article: How to Adjust Water Dispenser Thermostat: The Ultimate Guide.
Clean the reservoir
Primo water dispensers come with a reservoir at the top of the machine. This reservoir collects water, which is then dispensed through a push-lever arm. To clean the reservoir, use a mild detergent to remove any dirt and grime that has accumulated on the surface.
Pour this onto the reservoir and leave it to soak for 5 minutes. After soaking, rinse off the reservoir using cold water and dry it off with a paper towel or cloth. To clean the rest of the machine, fill up your sink or bathtub with hot water and pour some dishwashing liquid into it.
Put your Primo Water Dispenser in this solution and leave it for 30 minutes. After 30 minutes has passed, you may use a toothbrush or sponge to scrub the parts of your Primo Water Dispenser that are difficult to reach by hand. Rinse off all soap residue from your machine before drying it off with paper towel.
Disconnect the power cord and remove the fuse
The first thing you should do when disposing off a Primo water dispenser is to unplug the power cord. Then, remove the fuse and throw it away in a safe and secure place.
Disassemble the tank and clean it with a brush and soapy water
When you’re cleaning the tank, it’s important to first disassemble it. You can use a wrench or screwdriver to unscrew the bolts that hold the tank together. This will allow you to clean the tank easily and thoroughly.
After you have removed all of the bolts, remove any leftover water from inside and then clean the tank with a brush and soapy water. Be sure to use hot water if necessary as this will help remove any sticky residue left behind. Finally, rinse off all of the soap residue on the tank with warm water and dry it with a towel before reassembling it.
Clean the heating element and rinse it in cold water
As stated earlier, Primo water dispensers can dispense both hot and cold water. This means that the heating element is a key component to maintaining the machine. The heating element should be cleaned every two weeks to avoid mold and bacteria growth.
Fill a bowl with water and soak the heating element for about five minutes. Take a toothbrush dipped in soapy water and scrub any stubborn buildup off of the heating element. Rinse it off with cold water and place it back inside the machine.
A Guide to Buying a Primo Water Dispenser Heating Element
If you own a Primo water dispenser, you likely have come across the message “HEATING ELEMENT FAILED” at least once. Once you have read this error message and taken note of it, there’s little doubt that the heating element will fail again. Eventually, all heating elements fail on water dispensers.
The repair process is not difficult and usually takes no more than an hour to complete. However, it’s important to understand what is involved in replacing the heating element. This ensures you are prepared with the necessary tools and replacement parts in the event that your machine experiences this issue again.
What is a Primo Water Dispenser Heating Element?
A Primo water dispenser heating element is a small piece of metal that heats up to boil the water in the reservoir. It is not hard to replace this component if and when it fails, but you will need a few items before you get started. The Primo Water Dispenser Heating Element is part of the machine’s heating system and is located inside the machine near the bottom.
It’s important to note that this component does not heat up independently, but instead relies on electricity from the power cord to heat up. Replacing this part will help you avoid having to spend more money on repairs down the road.
How to Replace the Heating Element on a Primo Water Dispenser
In order to replace the heating element, you will need to remove the water dispenser from the countertop and unplug it. You will then need to remove the screws on the back panel that are holding it in place. After removing these screws, gently pry open the back panel with a flat head screwdriver and locate the heating element.
Remove the old heating element and replace it with a new one by following the instructions in your manual. Once this step is complete, close up your Primo water dispenser and reattach to your countertop.
Step by Step Instructions for Replacing a Primo Water Dispenser Heating Element
1. Disconnect the power cord from the back of the machine.
2. Remove the front panel and then pull out the drawer.
3. Unplug the connector from the bottom of the heating element. Be careful not to pull on the wire as it could break or cause damage to the wires inside your machine.
4. Unscrew both screws that are holding in place for your wiring harness, remove these screws and then carefully lift up on each side of your old heating element, pulling it out and away from your machine until you can disconnect it completely from its wiring harness, being careful not to touch any of its electrical components with your hands or other objects while you do so.
5. Carefully clean all residual water droplets around where you just removed your old heating element with a dry cloth before installing a new one (do not use water).
6. Install a new Primo water dispenser heating element by lining up its wiring harness connector with those that are in place near where you removed your old one. Plug them into each other securely and tightly before re-screwing them in place on either side of your machine’s wiring harness. Make sure they are snug but not too tight so as to cause damage to either part’s electrical components (be mindful that this is an electricity-conducting device).
7. Reattach your water pump by placing it back into place within its housing hole before screwing it.
Troubleshooting Tips for Replacing your Primo Water Dispenser Heating Element
If your Primo water dispenser is giving you a HEATING ELEMENT FAILED message, there are a few things to try before buying a replacement heating element. First, make sure the machine is plugged in and that it’s been given enough time to warm up. If the error message persists, leave the machine unplugged for a couple of hours.
Doing this will ensure that the coolness of the room won’t affect the water temperature. When replacing a heating element, it’s important to know which model of Primo water dispenser you have so you can buy the correct replacement. You can identify your model by looking at the serial number on the back of your machine or by taking off the front cover on your machine and looking at the sticker with your product model number printed on it.
You may contact your local dealer or visit primo water recycle center locations within your area. These help to handle any issues arising from your dispenser.
How does the heating element work?
The heating element is a critical component of your water dispenser. Its function is to heat the water that’s dispensed through your Primo water dispenser. The heating element is what keeps the tank hot and ready for use at all times.
When you turn on your Primo water dispenser, you should hear a humming noise coming from it as it heats up the tank. Once it has reached its set temperature, the noise will stop. This means that your water dispenser is ready to be used and there’s no need to wait for it to heat up or cool down again before using it.
When the heating element fails in a Primo water dispenser, this process will no longer take place and you may have noticed that there are gaps between when you get hot water from the machine. This could cause some inconvenience if you are trying to quickly fill a cup with a warm drink while out at work, school or in an office setting where people typically go back and forth with their coffee cups between shifts. Luckily, heating element replacements are not difficult and can be done by following these simple steps:
Conclusion
Primo water dispensers are a popular household appliance that helps you to reduce your use of plastic bottles and live a more sustainable lifestyle. However, over time the heating element inside of the water dispenser will wear out and will need to be replaced. Luckily, it’s not too difficult to replace the heating element on your Primo water dispenser and in this guide we will go over the necessary steps for removing and installing the heating element on your Primo water dispenser.
FAQS
How do I dispose of my Primo water dispenser?
Unlike other household objects, you may be unsure as to where and how you should dispose off your Primo water dispenser. The best place to dispose of your machine is at a recycling center. You can also find a number of recycling centers online which will allow you to search within a certain radius for the nearest location. If you cannot find one near you, then you can contact your local Primo service center. They will be able to supply you with the necessary information on how to proceed with disposing off your machine.
What are the dangers associated with disposing off this type of product?
The main danger associated with disposing off your Primo water dispenser is toxic chemical exposure. If the machine has not been maintained or cleaned properly, it could release dangerous chemicals into the environment when disposed off improperly or without care. This exposure can result in health problems and potentially even death if caution is not taken during disposal.
How do I clean my Primo water dispenser?
We recommend you clean your machine two to three times a week. To do this, use a solution of one part vinegar and one part water and soak the removable parts in it for 20 minutes. After soaking, rinse thoroughly with cold water.
What happens if I don’t clean my Primo water dispenser?
If you neglect to clean the removable parts, residue will form on them. This residue could potentially lead to mold or mildew growth on the machine, which can be harmful to both pets and humans.
Can I put my Primo water dispenser in the dishwasher?
No, you should never put your Primo water dispenser in the dishwasher as it will break down its plastic body over time.
How often should I change my filter?
You should change your filter once every six months or so, depending on how much you use your machine. You can find filters at most supermarkets and home improvement stores.
Conclusion
The Primo water dispenser is a great appliance to have in your kitchen, but what should you do if you want to get rid of it? The process of how to dispose of Primo Water Dispenser is not hard at all. All you need to do is follow the steps mentioned above and you are good to go.
You may also visit primo water recycle center locations near you for more information on disposal. They do provide other services as well, that you may be interested in.
