If you’ve ever had to deal with a water dispenser, you know how frustrating it can be. You have to buy bottled water and lug it home, or fill up a huge jug of water every day and haul it back to your house. It’s so inconvenient.
This article will show you How to Service Water Dispenser: The Ultimate Guide. We’ll start by going over the basics about what makes a good dispenser, then we’ll go over ways that you can make your life easier when dealing with one.
Finally, we’ll talk about the importance of keeping your dispenser clean and in working order by giving it a quick service once in awhile. So if you’re feeling thirsty, read on!
Check the Water Level
Depending on how your cooler is set up, you might find it very easy to check the water level inside. If you can see inside the cooler, use a measuring cup to check the water level. Remember to check the water level on each tap to make sure it’s consistent throughout the cooler.
If you can’t see inside the cooler to check the water level, you can easily measure it by removing the cooler’s plug and draining the water from it. Alternatively, you can use a water meter to measure the water level inside without removing the plug.
If the water level is below what is recommended, you’ll need to replace the water. However, if the level is just below the minimum, you can top it up with clean water. This will help prevent bacteria from building up and growing in the cooler.
Check the Filters
If you have a water cooler that uses filters, it’s a good idea to check and replace them once a month. If the filters haven’t been changed in a while and are full of debris, they could be restricting the flow of water and reducing the quality of the water.
To check your filters, remove them from the cooler and clean them, replacing them once they’re clean and dry again. If you don’t have a water cooler that uses filters, you can still check the water flow through the cooler by turning off the water supply and using a bucket to fill the cooler up with water.
Once the cooler is full, check to see if the water is flowing through the cooler correctly. If it doesn’t appear to be flowing, check the water supply and make sure it’s turned on correctly.
Check the Temperature
When you check the water temperature in your water cooler, you can also check if there are any leaks. If you notice that the water is warmer than it should be, it could be a sign of a leak.
If you notice the water is warmer than usual, try turning the cooler off and back on again.
If the temperature remains warm, you may have a leak. If the cooler is still under warranty, you can contact the manufacturer and have them repair it for you. If it’s out of warranty, you can have it repaired yourself.
Check the Taps and Nozzles
When you check the taps and nozzles on the water cooler, look for any signs of wear and tear. If the nozzles are bent, corroded, or have any damage to them, you’ll need to replace them.
The same goes for the taps, although this is less likely to happen. If there is any damage to the taps and nozzles, they can be easily replaced.
You can purchase new nozzles and taps from your local hardware store, or order them online if you’re unable to find them locally.
Check the Electronic Controls
Before you start to service the electronic controls, press the reset button on the cooler and make sure it’s off. If the cooler is still under warranty, by pressing the reset button it will reset the timer so it can’t detect an issue.
To check the electronic controls, use a multimeter to check the voltage across the circuit board. If the voltage reading is less than what’s recommended, you may have a faulty circuit board.
If this is the case, you’ll need to replace the circuit board.
Check the temperature and pressure of the water
If the cooler uses a carbonated water system, check the pressure at the end of the line. If the pressure is below what is recommended, you may have a leak.
Pressurizing carbonation systems can be tricky, so if you’re unsure how to do it, it’s best to leave it to someone who knows what they’re doing. If you’re not sure what the recommended pressure is, check the manufacturer’s manual for information.
If the pressure at the end of the line is too high, you can reduce it by installing a pressure regulator. Pressure regulators are designed to reduce the pressure at the end of the line, so you don’t need to get a new CO2 tank.
Check the filtration system and replace as needed
Depending on your water cooler, you may have a built-in filtration system. If you do, check it for damage or wear and tear, and replace it as needed.
If you don’t have a built-in filtration system, you can install a water filtration system in the cooler instead. If the water cooler is under warranty, you may be able to get the manufacturer to replace the water filtration system for you.
If it’s out of warranty, you can purchase replacement filtration systems online.
Check the water level
Before you start to service the cooler, check the water level inside. If it’s below what’s recommended, top up the water until it reaches the correct water level.
If you add water to the cooler and it leaks, you may have a leak in the cooler. If so, you’ll need to have it repaired, but you can do it yourself.
Check for leaks
If you’ve been servicing the cooler and the water level is above minimum, reset the cooler and close it up. Next, fill a bucket with water and actuate each tap on the cooler, checking for leaks.
If you notice a leak, turn off the tap and replace the washers or o-rings where needed. You can purchase washers and o-rings at any hardware store or online.
Check the carbonation system
If the cooler uses a carbonated water system, make sure it’s running correctly. If it’s not, you may have a leak in the system.
To check for leaks, follow the same steps as you would for leaks in the water system, but check the CO2 tank instead. When you’ve finished checking the CO2 tank, press the reset button on the cooler and make sure it’s off.
This will reset the timer so it can’t detect an issue with the CO2 tank.
Related article: How to Build a Lego Water Dispenser.
FAQS
Why is my water dispenser leaking?
If you have a dispenser that’s not turned on, then it may be running because of the pressure in the pipes. You can fix this by turning on the appliance and letting it run for a minute or two before switching off. If you have a leaky dispenser, your water may be contaminated and should be discarded.
What does “residual chlorine” mean?
It means chlorine has been added to the water to disinfect it, but chlorine is dangerous if ingested in large amounts. You can simply let your water sit overnight before drinking it. Chlorine will evaporate into the air, leaving you with safe drinking water.
Conclusion
If you’re interested in investing in a water dispenser, we recommend reading our easy-to-follow guide. Once you have your new dispenser, you’ll be ready to enjoy the benefits of fresh, clean water anytime!
And there are plenty of benefits to having a water dispenser at home. If you find yourself not drinking enough water, a water dispenser can encourage you to drink more. Or maybe you’re trying to lose weight and a water dispenser will help you achieve your goals.
